TASCO TIMETOOL WILL NOT EXECUTE SERIAL NUMBER
TASCO TIMETOOL WILL NOT EXECUTE INSTALL
TASCO TIMETOOL WILL NOT EXECUTE ZIP FILE
TASCO TIMETOOL WILL NOT EXECUTE UPDATE

The password can be obtained by emailing TimeTools at with the units serial number from the rear of the device.

Establish a serial connection between a PC and the T-Series unit, see: “RS232 Serial Port Settings For Console Connection” above.

Resetting the T-Series user password can only be acheived by logging into the device using the serial console cable supplied with the unit.

Press the key on the dumb terminal emulator a few times to establish a connection.

On the PC, use a dumb terminal emulator (such as putty) to connect to the device with the following settings: Connect Using: Direct to COMx (where x is the com port number).

Connect T-Series unit to PC RS232 serial port (or USB serial converter) using supplied console cable.

The T-Series can be configured using a dumb terminal emulator, running on a PC, connected to the devices console port using the supplied serial console lead. General System Queries RS232 Serial Port Settings For Console Connection The command operand depends on model and serial number.

TASCO TIMETOOL WILL NOT EXECUTE UPDATE

Use “ttgnssflash -res360” or “ttgnssflash -icm360” to manually update GNSS firmware from a CLI (SSH/Console) session. If the device is powered down during the GNSS update, the update may fail when power is reapplied. Syslog ‘Error Updating GNSS Firmware’ MessageĪfter updating to firmware 2.0.003, the device will attempt to update the GNSS firmware, if necessary. The 100m cable is a LMR400 equivalent cable. The 10m, 30m and 50m cables are a LMR195 equivalent cable.

TASCO TIMETOOL WILL NOT EXECUTE INSTALL

A crimp tool may be required to install a surge suppressor or to customize the length of the supplied cable. Standard lengths are 10m, 30m, 50m and 100m. TimeTools provide a range of cable lengths for use with T-Series models. Correct specification and installation of the antenna and cabling is paramount.Ĭheck here for tips and pointers on troubleshooting or improving your time servers GPS/GNSS signal reception. T-Series GPS and GNSS time servers utilize a remotely located active antenna separate from the server unit. Consider temporarily disabling Windows Firewall or any Anti-Virus software! GNSS / GPS Issues No GPS / GNSS Signal Lock Ensure that UDP port 69 is open on host PC firewall. Check what is the version of uboot that you have on the NTP server? See instructions page 6.Check that the TFTP port – TCP port 69 is not blocked by antivirus or Microsoft defender.

TASCO TIMETOOL WILL NOT EXECUTE ZIP FILE

Have you extracted the firmware update zip file to the ROOT TFTP directory.

Once configured, can you ping the TFTP sever from the NTP server?.

However, the instructions must be followed exactly. TFTP definitely works and is the preferred method of updating firmware – indeed we use it here to update our own servers. Updates are provided free of charge and can be downloaded here. To take advantage of new features, security updates and bug fixes, TimeTools recommends that customers regularly check that their T-Series network time servers firmware is up to date.

TimeTools provides regular firmware updates for all T-Series NTP servers. Ethernet Port Not Responding After Firmware Updateįirmware Update Queries Where To Obtain Firmware Updates.Issue Using “ip route add” in ‘Additional Network Configuration’ field.T550 Both NICS With Same IPv4 Subnet Mask.Adding a static route to the routing table.T-Series NTP Server Local Clock configuration.Device Powered Up But Display Blank and Alarm LED Off.Real Time Clock is Incorrect After Power Up.T-Series MTBF – Mean Time Between Failure.Testing SNMP Traps from the command line.Disabling ‘root’ and ‘timetools’ User Accounts.RS232 Serial Port Settings For Console Connection.Syslog ‘Error Updating GNSS Firmware’ Message.

Tasco timetool will not execute